Closed Water Tanks
Open Water Tanks
Large Capacity Water Tanks
Platinum Tanks range of large capacity potable water tanks are suitable for domestic, commercial and agricultural use. The entire range is manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. Every single skin water tank is fitted with a standard 1” BSP outlet for ease of installation, a 1/2” float valve and a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date.
The manufacturing process adheres to the ISO 9001:2015 quality standard and all single skin water storage tanks are visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality.
Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full the tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product.
As Standard
- 1” BSP Outlet
- Gauge Bung
- 1/2” Float Valve
- Ultrasonic Content Gauge
- Sight Gauge
- Clock Gauge
- 2” Fill Point
Platinum Tanks range of large capacity potable water tanks are suitable for domestic, commercial and agricultural use. The entire range is manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. Every single skin water tank is fitted with a standard 1” BSP outlet for ease of installation, a 1/2” float valve and a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date.
The manufacturing process adheres to the ISO 9001:2015 quality standard and all single skin water storage tanks are visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality.
Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full the tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product.
As Standard
- 1” BSP Outlet
- Gauge Bung
- 1/2” Float Valve
- Ultrasonic Content Gauge
- Sight Gauge
- Clock Gauge
- 2” Fill Point
Closed Water Tanks
Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. Every closed water tank comes with lids fitted and a float valve backing plate for easy installation of the float valve and overflow fitting.
Each product is visually inspected for defects using a light source and again prior to loading.
Installation Instructions:
- Inspect all tanks before installation as damage may occur during transport
- Ensure that the tank is fully supported
- Use a hole saw to drill holes in the tank
- The centre of the float valve should be 38mm from the top of the tank
- Do not install the tank close to a heat source such as a light or heater
- Polytank Lids
- Float Valve Backing Plate
- Drip Tray
Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. Every closed water tank comes with lids fitted and a float valve backing plate for easy installation of the float valve and overflow fitting.
Each product is visually inspected for defects using a light source and again prior to loading.
Installation Instructions:
- Inspect all tanks before installation as damage may occur during transport
- Ensure that the tank is fully supported
- Use a hole saw to drill holes in the tank
- The centre of the float valve should be 38mm from the top of the tank
- Do not install the tank close to a heat source such as a light or heater
- Polytank Lids
- Float Valve Backing Plate
- Drip Tray
Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. Every closed water tank comes with lids fitted and a float valve backing plate for easy installation of the float valve and overflow fitting.
Each product is visually inspected for defects using a light source and again prior to loading.
Installation Instructions:
- Inspect all tanks before installation as damage may occur during transport
- Ensure that the tank is fully supported
- Use a hole saw to drill holes in the tank
- The centre of the float valve should be 38mm from the top of the tank
- Do not install the tank close to a heat source such as a light or heater
- Polytank Lids
- Float Valve Backing Plate
- Drip Tray
Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. Every closed water tank comes with lids fitted and a float valve backing plate for easy installation of the float valve and overflow fitting.
Each product is visually inspected for defects using a light source and again prior to loading.
Installation Instructions:
- Inspect all tanks before installation as damage may occur during transport
- Ensure that the tank is fully supported
- Use a hole saw to drill holes in the tank
- The centre of the float valve should be 38mm from the top of the tank
- Do not install the tank close to a heat source such as a light or heater
- Polytank Lids
- Float Valve Backing Plate
- Drip Tray
Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. Every closed water tank comes with lids fitted and a float valve backing plate for easy installation of the float valve and overflow fitting.
Each product is visually inspected for defects using a light source and again prior to loading.
Installation Instructions:
- Inspect all tanks before installation as damage may occur during transport
- Ensure that the tank is fully supported
- Use a hole saw to drill holes in the tank
- The centre of the float valve should be 38mm from the top of the tank
- Do not install the tank close to a heat source such as a light or heater
- Polytank Lids
- Float Valve Backing Plate
- Drip Tray
Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. Every closed water tank comes with lids fitted and a float valve backing plate for easy installation of the float valve and overflow fitting.
Each product is visually inspected for defects using a light source and again prior to loading.
Installation Instructions:
- Inspect all tanks before installation as damage may occur during transport
- Ensure that the tank is fully supported
- Use a hole saw to drill holes in the tank
- The centre of the float valve should be 38mm from the top of the tank
- Do not install the tank close to a heat source such as a light or heater
- Polytank Lids
- Float Valve Backing Plate
- Drip Tray
Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. Every closed water tank comes with lids fitted and a float valve backing plate for easy installation of the float valve and overflow fitting.
Each product is visually inspected for defects using a light source and again prior to loading.
Installation Instructions:
- Inspect all tanks before installation as damage may occur during transport
- Ensure that the tank is fully supported
- Use a hole saw to drill holes in the tank
- The centre of the float valve should be 38mm from the top of the tank
- Do not install the tank close to a heat source such as a light or heater
- Polytank Lids
- Float Valve Backing Plate
- Drip Tray
Open Water Tanks
Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. A lid can be supplied to suit each open attic water storage tank.
Each product is visually inspected for defects using a light source and again prior to loading.
Installation Instructions:
- Inspect all tanks before installation as damage may occur during transport
- Ensure that the tank is fully supported
- Use a hole saw to drill holes in the tank
- The centre of the float valve should be 38mm from the top of the tank
- Do not install the tank close to a heat source such as a light or heater
- Lid
- Drip Tray
Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. A lid can be supplied to suit each open attic water storage tank.
Each product is visually inspected for defects using a light source and again prior to loading.
Installation Instructions:
- Inspect all tanks before installation as damage may occur during transport
- Ensure that the tank is fully supported
- Use a hole saw to drill holes in the tank
- The centre of the float valve should be 38mm from the top of the tank
- Do not install the tank close to a heat source such as a light or heater
- Lid
- Drip Tray
Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. A lid can be supplied to suit each open attic water storage tank.
Each product is visually inspected for defects using a light source and again prior to loading.
Installation Instructions:
- Inspect all tanks before installation as damage may occur during transport
- Ensure that the tank is fully supported
- Use a hole saw to drill holes in the tank
- The centre of the float valve should be 38mm from the top of the tank
- Do not install the tank close to a heat source such as a light or heater
- Lid
- Drip Tray
Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. A lid can be supplied to suit each open attic water storage tank.
Each product is visually inspected for defects using a light source and again prior to loading.
Installation Instructions:
- Inspect all tanks before installation as damage may occur during transport
- Ensure that the tank is fully supported
- Use a hole saw to drill holes in the tank
- The centre of the float valve should be 38mm from the top of the tank
- Do not install the tank close to a heat source such as a light or heater
- Lid
- Drip Tray
Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. A lid can be supplied to suit each open attic water storage tank.
Each product is visually inspected for defects using a light source and again prior to loading.
Installation Instructions:
- Inspect all tanks before installation as damage may occur during transport
- Ensure that the tank is fully supported
- Use a hole saw to drill holes in the tank
- The centre of the float valve should be 38mm from the top of the tank
- Do not install the tank close to a heat source such as a light or heater
- Lid
- Drip Tray
Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. A lid can be supplied to suit each open attic water storage tank.
Each product is visually inspected for defects using a light source and again prior to loading.
Installation Instructions:
- Inspect all tanks before installation as damage may occur during transport
- Ensure that the tank is fully supported
- Use a hole saw to drill holes in the tank
- The centre of the float valve should be 38mm from the top of the tank
- Do not install the tank close to a heat source such as a light or heater
- Lid
- Drip Tray
Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. A lid can be supplied to suit each open attic water storage tank.
Each product is visually inspected for defects using a light source and again prior to loading.
Installation Instructions:
- Inspect all tanks before installation as damage may occur during transport
- Ensure that the tank is fully supported
- Use a hole saw to drill holes in the tank
- The centre of the float valve should be 38mm from the top of the tank
- Do not install the tank close to a heat source such as a light or heater
- Lid
- Drip Tray
Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. A lid can be supplied to suit each open attic water storage tank.
Each product is visually inspected for defects using a light source and again prior to loading.
Installation Instructions:
- Inspect all tanks before installation as damage may occur during transport
- Ensure that the tank is fully supported
- Use a hole saw to drill holes in the tank
- The centre of the float valve should be 38mm from the top of the tank
- Do not install the tank close to a heat source such as a light or heater
- Lid
- Drip Tray
Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. A lid can be supplied to suit each open attic water storage tank.
Each product is visually inspected for defects using a light source and again prior to loading.
Installation Instructions:
- Inspect all tanks before installation as damage may occur during transport
- Ensure that the tank is fully supported
- Use a hole saw to drill holes in the tank
- The centre of the float valve should be 38mm from the top of the tank
- Do not install the tank close to a heat source such as a light or heater
- Lid
- Drip Tray
Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. A lid can be supplied to suit each open attic water storage tank.
Each product is visually inspected for defects using a light source and again prior to loading.
Installation Instructions:
- Inspect all tanks before installation as damage may occur during transport
- Ensure that the tank is fully supported
- Use a hole saw to drill holes in the tank
- The centre of the float valve should be 38mm from the top of the tank
- Do not install the tank close to a heat source such as a light or heater
- Lid
- Drip Tray
Large Capacity Water Tanks
Platinum Tanks range of large capacity potable water tanks are suitable for domestic, commercial and agricultural use. The entire range is manufactured from UV stabilised linear low density polyethylene to protect the product from UV degrad
Read More
Length:
Width:
Height:
Capacity:
Warranty:
Diameter:
Platinum Tanks range of large capacity potable water tanks are suitable for domestic, commercial and agricultural use. The entire range is manufactured from UV stabilised linear low density polyethylene to protect the product from UV degrad
Read More
Length:
1,770mm (70″)
Width:
660mm (26″)
Height:
1,270mm (50″)
Capacity:
1,150 Litres (252 Gallons)
Warranty:
2 Years on Manufacturing Defects
Diameter:
Closed Water Tanks
Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. Every closed water tank comes with lids fitted and a float va
Read More
Length:
690mm (27″)
Width:
515mm (20″)
Height:
520mm (20″)
Capacity:
114 Litres (25 Gallons)
Warranty:
1 Year on Manufacturing Defects
Diameter:
Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. Every closed water tank comes with lids fitted and a float va
Read More
Length:
1,390mm (55″)
Width:
500mm (20″)
Height:
310mm (12″)
Capacity:
114 Litres (25 Gallons)
Warranty:
1 Year on Manufacturing Defects
Diameter:
Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. Every closed water tank comes with lids fitted and a float va
Read More
Length:
1,640mm 64″
Width:
450mm 18″
Height:
485mm 19″
Capacity:
227 Litres (50 Gallons)
Warranty:
1 Year on Manufacturing Defects
Diameter:
Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. Every closed water tank comes with lids fitted and a float va
Read More
Length:
1,185mm (46″)
Width:
503mm (19″)
Height:
503mm (19″)
Capacity:
190 Litres (42 Gallons)
Warranty:
1 Year on Manufacturing Defects
Diameter:
Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. Every closed water tank comes with lids fitted and a float va
Read More
Length:
1,650mm (64″)
Width:
610mm (24″)
Height:
475mm (19″)
Capacity:
318 Litres (70 Gallons)
Warranty:
1 Year on Manufacturing Defects
Diameter:
Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. Every closed water tank comes with lids fitted and a float va
Read More
Length:
1,185mm (46″)
Width:
503mm (19″)
Height:
503mm (19″)
Capacity:
190 Litres (42 Gallons)
Warranty:
1 Year on Manufacturing Defects
Diameter:
Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. Every closed water tank comes with lids fitted and a float va
Read More
Length:
1,670mm (64″)
Width:
690mm (26″)
Height:
580mm (23″)
Capacity:
454 Litres (100 Gallons)
Warranty:
1 Year on Manufacturing Defects
Diameter:
Open Water Tanks
Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. A lid can be supplied to suit each open attic water storage t
Read More
Length:
1,260mm (49.6″)
Width:
660mm (26.0″)
Height:
530mm (20.9″)
Capacity:
182 Litres (40 Gallons)
Warranty:
1 Year on Manufacturing Defects
Diameter:
Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. A lid can be supplied to suit each open attic water storage t
Read More
Length:
1,336mm (52.6″)
Width:
470mm (18.5″)
Height:
455mm (17.9″)
Capacity:
150 Litres (33 Gallons)
Warranty:
1 Year on Manufacturing Defects
Diameter:
Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. A lid can be supplied to suit each open attic water storage t
Read More
Length:
1,575mm (62.0″)
Width:
525mm (20.7″)
Height:
580mm (22.8″)
Capacity:
236 Litres (52 Gallons)
Warranty:
1 Year on Manufacturing Defects
Diameter:
Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. A lid can be supplied to suit each open attic water storage t
Read More
Length:
1,790mm (70.75″)
Width:
550mm (21.5″)
Height:
550mm (21.5″)
Capacity:
318 Litres (70 Gallons)
Warranty:
1 Year on Manufacturing Defects
Diameter:
Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. A lid can be supplied to suit each open attic water storage t
Read More
Length:
1,440mm (56.73″)
Width:
790mm (31.9″)
Height:
660mm (26.0″)
Capacity:
454 Litres (100 Gallons)
Warranty:
1 Year on Manufacturing Defects
Diameter:
Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. A lid can be supplied to suit each open attic water storage t
Read More
Length:
600mm (23.7″)
Width:
600mm (23.7″)
Height:
1,090mm (43″)
Capacity:
270 Litres (59 Gallons)
Warranty:
1 Year on Manufacturing Defects
Diameter:
Length:
Width:
Height:
Capacity:
Length:
450mm (17.7″)
Width:
315mm (12.4″)
Height:
300mm (11.8″)
Capacity:
18 Litres (4 Gallons)
Warranty:
1 Year on Manufacturing Defects
Diameter:
Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. A lid can be supplied to suit each open attic water storage t
Read More
Length:
780mm (30.7″)
Width:
480mm (18.9″)
Height:
470mm (18.5″)
Capacity:
91 Litres (20 Gallons)
Warranty:
1 Year on Manufacturing Defects
Diameter:
Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. A lid can be supplied to suit each open attic water storage t
Read More
Length:
1,160mm (45.7″)
Width:
460mm (18.1″)
Height:
460mm (18.1″)
Capacity:
123 Litres (27 Gallons)
Warranty:
1 Year on Manufacturing Defects
Diameter:
Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. A lid can be supplied to suit each open attic water storage t
Read More
Length:
1,100mm (43.3″)
Width:
570mm (22.4″)
Height:
530mm (20.9″)
Capacity:
197 Litres (43 Gallons)
Warranty:
1 Year on Manufacturing Defects
Diameter:
Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. A lid can be supplied to suit each open attic water storage t
Read More
Length:
870mm (34.3″)
Width:
595mm (23.5″)
Height:
610mm (24.0″)
Capacity:
150 Litres (33 Gallons)
Warranty:
1 Year on Manufacturing Defects
Diameter:
Drip Trays