• Manufactured from medium/high density polyethylene.
• Robust construction by design.
• UV stabilised and suitable for all weather conditions.
• Fitted with tie down points to secure the trough to the feed barrier.
• Fill point and output bung to allow weighing down with water if desired.
• The barrier troughs are very durable and lightweight thus making moving them for access to pens very easy.

• Manufactured from medium/high density polyethylene.
• Robust construction by design.
• UV stabilised and suitable for all weather conditions.
• All Platunum Drinkers come complete with 1/2 inch high pressure ball valves as standard. The design of the ball housing helps ensure the animals cannot damage the ball valve. They can also be fitted with larger ball valves on request.
• Drinkers are maintenance free.
• The livestock drinkers are very durable and lightweight thus making moving from pasture to pasture easy.
• 138 Litres / 30 Gallons.
• All drinkers need to be handled with care.

 

• Designed to enable transport using a standard bale lifter.
• Manufactured from medium/high density polyethylene.
• Robust construction by design.
• UV stabilised and suitable for all weather conditions.
• The meal bins are very durable and lightweight thus making moving from pasture to pasture easy.
• Can carry over 700kg of animal feed depending on the feed type.

A plastic head scoop used to hold the animals head so that one person can safely administer medication. The product has nuts moulded into a recess in the body for easy installation on a metal frame. Metal frame is not included. Click here to view a video of a head scoop in action.

• Manufactured from medium/high density polyethylene.
• Robust construction by design.
• UV stabilised and suitable for all weather conditions.
• Footbaths are maintenance free.
• Plastic Footbaths are very durable and lightweight thus making moving easy.

• Manufactured from medium/high density polyethylene.
• Robust construction by design.
• UV stabilised and suitable for all weather conditions.
• Chemical stores are very durable and lightweight thus making moving from pasture to pasture easy.
• Containment area in base of storage bin with bung for safe drainage of any leaked chemicals.
• 454 Litres (100 Gallons)

• Manufactured from medium/high density polyethylene.
• Robust construction by design.
• UV stabilised and suitable for all weather conditions.
• Fitted with two swivel castor wheels and two fixed castor wheels for easy manoeuvrability.
• Material handling trolleys are very durable and lightweight thus making moving from pasture to pasture easy.

Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date. The single skin inner tanks are manufactured to European Standard EN13343. Note: Currently there is no European Standard for bund outers, the standard is in progress at the moment and when it becomes law, all Platinum Bund outers will be tested to this standard. Both the inner tank and bund outer are manufactured to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality. Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information. Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product. As Standard

• 1” BSP Outlet
• Gauge Bung

  Options

• Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
• Ultrasonic Content Gauge
• Sight Gauge
• Clock Gauge
• Top outlet with Anti-Syphon
• 2” Fill Point
• 2” Overspill Prevention

Platinum Tanks range of large capacity potable water tanks are suitable for domestic, commercial and agricultural use. The entire range is manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. Every single skin water tank is fitted with a standard 1” BSP outlet for ease of installation, a 1/2” float valve and a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date. The manufacturing process adheres to the ISO 9001:2015 quality standard and all single skin water storage tanks are visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality. Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full the tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product. As Standard

• 1” BSP Outlet
• Gauge Bung
• 1/2” Float Valve

Options

• Ultrasonic Content Gauge
• Sight Gauge
• Clock Gauge
• 2” Fill Point

Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date. All single skin oil storage tanks are manufactured to European Standard EN13343 and the manufacturing process adheres to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality. Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information. Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product. As Standard

• 1” BSP Outlet
• Gauge Bung

Options

• Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
• Ultrasonic Content Gauge
• Sight Gauge
• Clock Gauge
• Top outlet with Anti-Syphon
• 2” Fill Point
• 2” Overspill Prevention

Platinum Tanks range of large capacity potable water tanks are suitable for domestic, commercial and agricultural use. The entire range is manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. Every single skin water tank is fitted with a standard 1” BSP outlet for ease of installation, a 1/2” float valve and a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date. The manufacturing process adheres to the ISO 9001:2015 quality standard and all single skin water storage tanks are visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality. Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full the tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product. As Standard

• 1” BSP Outlet
• Gauge Bung
• 1/2” Float Valve

Options

• Ultrasonic Content Gauge
• Sight Gauge
• Clock Gauge
• 2” Fill Point

Handles: 2 Handle Craneable

Handles: 4 Handle Teleporter Capacity:

The Platinum Forecourt Bunker provides a secure lockable display unit for shops and forecourts. It is also ideal for households as a storage container.

• Available in Blue, Black, Green & Red.
• They are rot and rust proof.
• The Forecourt Bunker is manufactured from a UV stabilized medium grade polyethylene.
• The Forecourt Bunker is suitable for storing products such as coal, briquettes and wood. Typical capacity of bunker is 30 x 25kg bags.
• The lid of the Forecourt Bunker is fully retractable for displaying products.

 

The Platinum Tanks grit bin range offers customers storage solutions for sand and salt.

• Available in highly visible colours e.g. Yellow
• These bunkers are designed for strength.
• Indoor and outdoor use.
• They have a top and bottom opening for easy access.
• They are manufactured from UV resistant medium density polyethylene.
• No maintenance required as they will not rot or rust.

The Platinum Tanks grit bin range offers customers storage solutions for sand and salt.

• Available in highly visible colours e.g. Yellow
• These bunkers are designed for strength.
• Indoor and outdoor use.
• They have a top and bottom opening for easy access.
• They are manufactured from UV resistant medium density polyethylene.
• No maintenance required as they will not rot or rust.

The Platinum Tanks grit bin range offers customers storage solutions for sand and salt.

• Available in highly visible colours e.g. Yellow
• These bunkers are designed for strength.
• Indoor and outdoor use.
• They have a top and bottom opening for easy access.
• They are manufactured from UV resistant medium density polyethylene.
• No maintenance required as they will not rot or rust.

The Platinum Tanks grit bin range offers customers storage solutions for sand and salt.

• Available in highly visible colours e.g. Yellow
• These bunkers are designed for strength.
• Indoor and outdoor use.
• They have a top and bottom opening for easy access.
• They are manufactured from UV resistant medium density polyethylene.
• No maintenance required as they will not rot or rust.

 

Platinum Tanks range of bunkers offer customers a sturdy solutions for all their solid fuel and domestic storage needs. Available in black and green, all bunkers are manufactured from UV stabilised medium density polyethylene to protect the product from UV degradation. The manufacturing process adheres to the ISO 9001:2015 quality standard. Features

• Available in Black and Green.
• These bunkers are designed for strength.
• Indoor and outdoor use.
• They have a top and bottom opening for easy access.
• They are manufactured from UV resistant medium density polyethylene.
• No maintenance required as they will not rot or rust.

Length: Width: Height: Capacity:

Platinum Tanks range of bunkers offer customers a sturdy solutions for all their solid fuel and domestic storage needs. Available in black and green, all bunkers are manufactured from UV stabilised medium density polyethylene to protect the product from UV degradation. The manufacturing process adheres to the ISO 9001:2015 quality standard. Features

• Available in Black and Green.
• These bunkers are designed for strength.
• Indoor and outdoor use.
• They have a top and bottom opening for easy access.
• They are manufactured from UV resistant medium density polyethylene.

• No maintenance required as they will not rot or rust.

Platinum Tanks range of bunkers offer customers a sturdy solutions for all their solid fuel and domestic storage needs. Available in black and green, all bunkers are manufactured from UV stabilised medium density polyethylene to protect the product from UV degradation. The manufacturing process adheres to the ISO 9001:2015 quality standard. Features

• Available in Black and Green.
• These bunkers are designed for strength.
• Indoor and outdoor use.
• They have a top and bottom opening for easy access.
• They are manufactured from UV resistant medium density polyethylene.

• No maintenance required as they will not rot or rust.

• Manufactured from medium/high density polyethylene.
• Robust construction by design.
• UV stabilised and suitable for all weather conditions.
• All Platunum Drinkers come complete with 1/2 inch high pressure ball valves as standard. The design of the ball housing helps ensure the animals cannot damage the ball valve. They can also be fitted with larger ball valves on request.
• Drinkers are maintenance free.
• The livestock drinkers are very durable and lightweight thus making moving from pasture to pasture easy.
• 1135 Litres / 250 Gallons.
• All drinkers need to be handled with care.

Diameter: 1,725mm  

• Manufactured from medium/high density polyethylene.
• Robust construction by design.
• UV stabilised and suitable for all weather conditions.
• All Platunum Drinkers come complete with 1/2 inch high pressure ball valves as standard. The design of the ball housing helps ensure the animals cannot damage the ball valve. They can also be fitted with larger ball valves on request.
• Drinkers are maintenance free.
• The livestock drinkers are very durable and lightweight thus making moving from pasture to pasture easy.
• 410 Litres / 90 Gallons.
• All drinkers need to be handled with care.

 

• Manufactured from medium/high density polyethylene.
• Robust construction by design.
• UV stabilised and suitable for all weather conditions.
• All Platunum Drinkers come complete with 1/2 inch high pressure ball valves as standard. The design of the ball housing helps ensure the animals cannot damage the ball valve. They can also be fitted with larger ball valves on request.
• Drinkers are maintenance free.
• The livestock drinkers are very durable and lightweight thus making moving from pasture to pasture easy.
• 180 Litres / 40 Gallons.
• All drinkers need to be handled with care.

 

• Manufactured from medium/high density polyethylene.
• Robust construction by design.
• UV stabilised and suitable for all weather conditions.
• All Platunum Drinkers come complete with 1/2 inch high pressure ball valves as standard. The design of the ball housing helps ensure the animals cannot damage the ball valve. They can also be fitted with larger ball valves on request.
• Drinkers are maintenance free.
• The livestock drinkers are very durable and lightweight thus making moving from pasture to pasture easy.
• 54 Litres / 12 Gallons.
• All drinkers need to be handled with care.

 

Platinum Tanks range of oil storage tanks are suitable for use as gravity feed fuel tanks. The tanks can be fitted with a hose pack and auto cut off nozzle. All fuel storage tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is fitted to every tank for ease of installation. Each fuel tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date. All products are manufactured to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality. Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information. Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product. As Standard

• 4m Hose Pack with Auto Shut-Off Nozzle
• Gauge Bung

  Options

• Alternative Hose Lengths
• Ultrasonic Content Gauge
• Sight Gauge
• Clock Gauge
• Top outlet with Anti-Syphon
• 2” Fill Point
• 2” Overspill Prevention

Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. Every closed water tank comes with lids fitted and a float valve backing plate for easy installation of the float valve and overflow fitting. Each product is visually inspected for defects using a light source and again prior to loading. Installation Instructions:

1. Inspect all tanks before installation as damage may occur during transport
2. Ensure that the tank is fully supported
3. Use a hole saw to drill holes in the tank
4. The centre of the float valve should be 38mm from the top of the tank
5. Do not install the tank close to a heat source such as a light or heater

Warning: To ensure uniform loading of the product, water storage tanks must be installed on a flat non-deformable base which extends beyond the product on all sides. Failure to meet this requirement will void all warranties on the product. As Standard

• Polytank Lids
• Float Valve Backing Plate

Options

• Drip Tray

Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. Every closed water tank comes with lids fitted and a float valve backing plate for easy installation of the float valve and overflow fitting. Each product is visually inspected for defects using a light source and again prior to loading. Installation Instructions:

1. Inspect all tanks before installation as damage may occur during transport
2. Ensure that the tank is fully supported
3. Use a hole saw to drill holes in the tank
4. The centre of the float valve should be 38mm from the top of the tank
5. Do not install the tank close to a heat source such as a light or heater

Warning: To ensure uniform loading of the product, water storage tanks must be installed on a flat non-deformable base which extends beyond the product on all sides. Failure to meet this requirement will void all warranties on the product. As Standard

• Polytank Lids
• Float Valve Backing Plate

Options

• Drip Tray

Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. Every closed water tank comes with lids fitted and a float valve backing plate for easy installation of the float valve and overflow fitting. Each product is visually inspected for defects using a light source and again prior to loading. Installation Instructions:

1. Inspect all tanks before installation as damage may occur during transport
2. Ensure that the tank is fully supported
3. Use a hole saw to drill holes in the tank
4. The centre of the float valve should be 38mm from the top of the tank
5. Do not install the tank close to a heat source such as a light or heater

Warning: To ensure uniform loading of the product, water storage tanks must be installed on a flat non-deformable base which extends beyond the product on all sides. Failure to meet this requirement will void all warranties on the product. As Standard

• Polytank Lids
• Float Valve Backing Plate

Options

• Drip Tray

Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. Every closed water tank comes with lids fitted and a float valve backing plate for easy installation of the float valve and overflow fitting. Each product is visually inspected for defects using a light source and again prior to loading. Installation Instructions:

1. Inspect all tanks before installation as damage may occur during transport
2. Ensure that the tank is fully supported
3. Use a hole saw to drill holes in the tank
4. The centre of the float valve should be 38mm from the top of the tank
5. Do not install the tank close to a heat source such as a light or heater

Warning: To ensure uniform loading of the product, water storage tanks must be installed on a flat non-deformable base which extends beyond the product on all sides. Failure to meet this requirement will void all warranties on the product. As Standard

• Polytank Lids
• Float Valve Backing Plate

Options

• Drip Tray

Length: Width: Height: Capacity:

Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. Every closed water tank comes with lids fitted and a float valve backing plate for easy installation of the float valve and overflow fitting. Each product is visually inspected for defects using a light source and again prior to loading. Installation Instructions:

1. Inspect all tanks before installation as damage may occur during transport
2. Ensure that the tank is fully supported
3. Use a hole saw to drill holes in the tank
4. The centre of the float valve should be 38mm from the top of the tank
5. Do not install the tank close to a heat source such as a light or heater

Warning: To ensure uniform loading of the product, water storage tanks must be installed on a flat non-deformable base which extends beyond the product on all sides. Failure to meet this requirement will void all warranties on the product. As Standard

• Polytank Lids
• Float Valve Backing Plate

Options

• Drip Tray

Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. A lid can be supplied to suit each open attic water storage tank. Each product is visually inspected for defects using a light source and again prior to loading. Installation Instructions:

1. Inspect all tanks before installation as damage may occur during transport
2. Ensure that the tank is fully supported
3. Use a hole saw to drill holes in the tank
4. The centre of the float valve should be 38mm from the top of the tank
5. Do not install the tank close to a heat source such as a light or heater

Warning: To ensure uniform loading of the product, water storage tanks must be installed on a flat non-deformable base which extends beyond the product on all sides. Failure to meet this requirement will void all warranties on the product.   Options

• Lid
• Drip Tray

Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. A lid can be supplied to suit each open attic water storage tank. Each product is visually inspected for defects using a light source and again prior to loading. Installation Instructions:

1. Inspect all tanks before installation as damage may occur during transport
2. Ensure that the tank is fully supported
3. Use a hole saw to drill holes in the tank
4. The centre of the float valve should be 38mm from the top of the tank
5. Do not install the tank close to a heat source such as a light or heater

Warning: To ensure uniform loading of the product, water storage tanks must be installed on a flat non-deformable base which extends beyond the product on all sides. Failure to meet this requirement will void all warranties on the product.   Options

• Lid
• Drip Tray

Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. A lid can be supplied to suit each open attic water storage tank. Each product is visually inspected for defects using a light source and again prior to loading. Installation Instructions:

1. Inspect all tanks before installation as damage may occur during transport
2. Ensure that the tank is fully supported
3. Use a hole saw to drill holes in the tank
4. The centre of the float valve should be 38mm from the top of the tank
5. Do not install the tank close to a heat source such as a light or heater

Warning: To ensure uniform loading of the product, water storage tanks must be installed on a flat non-deformable base which extends beyond the product on all sides. Failure to meet this requirement will void all warranties on the product.   Options

• Lid
• Drip Tray

Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. A lid can be supplied to suit each open attic water storage tank. Each product is visually inspected for defects using a light source and again prior to loading. Installation Instructions:

1. Inspect all tanks before installation as damage may occur during transport
2. Ensure that the tank is fully supported
3. Use a hole saw to drill holes in the tank
4. The centre of the float valve should be 38mm from the top of the tank
5. Do not install the tank close to a heat source such as a light or heater

Warning: To ensure uniform loading of the product, water storage tanks must be installed on a flat non-deformable base which extends beyond the product on all sides. Failure to meet this requirement will void all warranties on the product.   Options

• Lid
• Drip Tray

Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. A lid can be supplied to suit each open attic water storage tank. Each product is visually inspected for defects using a light source and again prior to loading. Installation Instructions:

1. Inspect all tanks before installation as damage may occur during transport
2. Ensure that the tank is fully supported
3. Use a hole saw to drill holes in the tank
4. The centre of the float valve should be 38mm from the top of the tank
5. Do not install the tank close to a heat source such as a light or heater

Warning: To ensure uniform loading of the product, water storage tanks must be installed on a flat non-deformable base which extends beyond the product on all sides. Failure to meet this requirement will void all warranties on the product.   Options

• Lid
• Drip Tray

Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. A lid can be supplied to suit each open attic water storage tank. Each product is visually inspected for defects using a light source and again prior to loading. Installation Instructions:

1. Inspect all tanks before installation as damage may occur during transport
2. Ensure that the tank is fully supported
3. Use a hole saw to drill holes in the tank
4. The centre of the float valve should be 38mm from the top of the tank
5. Do not install the tank close to a heat source such as a light or heater

Warning: To ensure uniform loading of the product, water storage tanks must be installed on a flat non-deformable base which extends beyond the product on all sides. Failure to meet this requirement will void all warranties on the product.   Options

• Lid
• Drip Tray

Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. A lid can be supplied to suit each open attic water storage tank. Each product is visually inspected for defects using a light source and again prior to loading. Installation Instructions:

1. Inspect all tanks before installation as damage may occur during transport
2. Ensure that the tank is fully supported
3. Use a hole saw to drill holes in the tank
4. The centre of the float valve should be 38mm from the top of the tank
5. Do not install the tank close to a heat source such as a light or heater

Warning: To ensure uniform loading of the product, water storage tanks must be installed on a flat non-deformable base which extends beyond the product on all sides. Failure to meet this requirement will void all warranties on the product.   Options

• Lid
• Drip Tray

Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. A lid can be supplied to suit each open attic water storage tank. Each product is visually inspected for defects using a light source and again prior to loading. Installation Instructions:

1. Inspect all tanks before installation as damage may occur during transport
2. Ensure that the tank is fully supported
3. Use a hole saw to drill holes in the tank
4. The centre of the float valve should be 38mm from the top of the tank
5. Do not install the tank close to a heat source such as a light or heater

Warning: To ensure uniform loading of the product, water storage tanks must be installed on a flat non-deformable base which extends beyond the product on all sides. Failure to meet this requirement will void all warranties on the product.   Options

• Lid
• Drip Tray

Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. A lid can be supplied to suit each open attic water storage tank. Each product is visually inspected for defects using a light source and again prior to loading. Installation Instructions:

1. Inspect all tanks before installation as damage may occur during transport
2. Ensure that the tank is fully supported
3. Use a hole saw to drill holes in the tank
4. The centre of the float valve should be 38mm from the top of the tank
5. Do not install the tank close to a heat source such as a light or heater

Warning: To ensure uniform loading of the product, water storage tanks must be installed on a flat non-deformable base which extends beyond the product on all sides. Failure to meet this requirement will void all warranties on the product.   Options

• Lid
• Drip Tray

Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. A lid can be supplied to suit each open attic water storage tank. Each product is visually inspected for defects using a light source and again prior to loading. Installation Instructions:

1. Inspect all tanks before installation as damage may occur during transport
2. Ensure that the tank is fully supported
3. Use a hole saw to drill holes in the tank
4. The centre of the float valve should be 38mm from the top of the tank
5. Do not install the tank close to a heat source such as a light or heater

Warning: To ensure uniform loading of the product, water storage tanks must be installed on a flat non-deformable base which extends beyond the product on all sides. Failure to meet this requirement will void all warranties on the product.   Options

• Lid
• Drip Tray

Length: Width: Height: Capacity:

Platinum Tanks range of bunded fuel stations feature a piusi fuel pump fitted with a 10 micron particulate filter and a 4m hose with automatic shut-off nozzle. Both the inner tank and bund outer are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 2” fill point is fitted to the inner tank to enable easy filling of the inner tank. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date. Platinum Tanks bunded fuel stations are manufactured to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality. Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information. Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product. As Standard

• Piusi Pump
• 4m Hose Pack with Auto Shut-Off Nozzle
• Gauge Bung

  Options

• Alternative Hose Lengths
• Ultrasonic Content Gauge
• Sight Gauge
• Clock Gauge
• Top outlet with Anti-Syphon
• 2” Fill Point
• 2” Overspill Prevention

  Diameter Min: 2,190mm 86.22″ Diameter Max: 2,890mm 113.78″

Platinum Tanks range of bunded fuel stations feature a piusi fuel pump fitted with a 10 micron particulate filter and a 4m hose with automatic shut-off nozzle. Both the inner tank and bund outer are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 2” fill point is fitted to the inner tank to enable easy filling of the inner tank. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date. Platinum Tanks bunded fuel stations are manufactured to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality. Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information. Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product. As Standard

• Piusi Pump
• 4m Hose Pack with Auto Shut-Off Nozzle
• Gauge Bung

  Options

• Alternative Hose Lengths
• Ultrasonic Content Gauge
• Sight Gauge
• Clock Gauge
• Top outlet with Anti-Syphon
• 2” Fill Point
• 2” Overspill Prevention

Platinum Tanks range of bunded fuel stations feature a piusi fuel pump fitted with a 10 micron particulate filter and a 4m hose with automatic shut-off nozzle. Both the inner tank and bund outer are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 2” fill point is fitted to the inner tank to enable easy filling of the inner tank. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date. Platinum Tanks bunded fuel stations are manufactured to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality. Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information. Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product. As Standard

• Piusi Pump
• 4m Hose Pack with Auto Shut-Off Nozzle
• Gauge Bung

Options

• Alternative Hose Lengths
• Ultrasonic Content Gauge
• Sight Gauge
• Clock Gauge
• Top outlet with Anti-Syphon
• 2” Fill Point
• 2” Overspill Prevention

Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date. The single skin inner tanks are manufactured to European Standard EN13343. Note: Currently there is no European Standard for bund outers, the standard is in progress at the moment and when it becomes law, all Platinum Bund outers will be tested to this standard. Both the inner tank and bund outer are manufactured to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality. Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information. Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product. As Standard

• 1” BSP Outlet
• Gauge Bung

  Options

• Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
• Ultrasonic Content Gauge
• Sight Gauge
• Clock Gauge
• Top outlet with Anti-Syphon
• 2” Fill Point
• 2” Overspill Prevention

  Diameter: 2,190mm 86.22″

Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date. The single skin inner tanks are manufactured to European Standard EN13343. Note: Currently there is no European Standard for bund outers, the standard is in progress at the moment and when it becomes law, all Platinum Bund outers will be tested to this standard. Both the inner tank and bund outer are manufactured to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality. Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information. Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product. As Standard

• 1” BSP Outlet
• Gauge Bung

  Options

• Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
• Ultrasonic Content Gauge
• Sight Gauge
• Clock Gauge
• Top outlet with Anti-Syphon
• 2” Fill Point
• 2” Overspill Prevention

  Diameter: 1,900mm 74.80″

Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date. The single skin inner tanks are manufactured to European Standard EN13343. Note: Currently there is no European Standard for bund outers, the standard is in progress at the moment and when it becomes law, all Platinum Bund outers will be tested to this standard. Both the inner tank and bund outer are manufactured to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality. Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information. Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product. As Standard

• 1” BSP Outlet
• Gauge Bung

  Options

• Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
• Ultrasonic Content Gauge
• Sight Gauge
• Clock Gauge
• Top outlet with Anti-Syphon
• 2” Fill Point
• 2” Overspill Prevention

  Diameter: 1,440mm 55.69″

Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date. The single skin inner tanks are manufactured to European Standard EN13343. Note: Currently there is no European Standard for bund outers, the standard is in progress at the moment and when it becomes law, all Platinum Bund outers will be tested to this standard. Both the inner tank and bund outer are manufactured to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality. Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information. Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product. As Standard

• 1” BSP Outlet
• Gauge Bung

  Options

• Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
• Ultrasonic Content Gauge
• Sight Gauge
• Clock Gauge
• Top outlet with Anti-Syphon
• 2” Fill Point
• 2” Overspill Prevention

 

Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date. The single skin inner tanks are manufactured to European Standard EN13343. Note: Currently there is no European Standard for bund outers, the standard is in progress at the moment and when it becomes law, all Platinum Bund outers will be tested to this standard. Both the inner tank and bund outer are manufactured to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality. Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information. Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product. As Standard

• 1” BSP Outlet
• Gauge Bung

  Options

• Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
• Ultrasonic Content Gauge
• Sight Gauge
• Clock Gauge
• Top outlet with Anti-Syphon
• 2” Fill Point
• 2” Overspill Prevention

Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date. The single skin inner tanks are manufactured to European Standard EN13343. Note: Currently there is no European Standard for bund outers, the standard is in progress at the moment and when it becomes law, all Platinum Bund outers will be tested to this standard. Both the inner tank and bund outer are manufactured to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality. Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information. Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product. As Standard

• 1” BSP Outlet
• Gauge Bung

  Options

• Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
• Ultrasonic Content Gauge
• Sight Gauge
• Clock Gauge
• Top outlet with Anti-Syphon
• 2” Fill Point
• 2” Overspill Prevention

Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date. The single skin inner tanks are manufactured to European Standard EN13343. Note: Currently there is no European Standard for bund outers, the standard is in progress at the moment and when it becomes law, all Platinum Bund outers will be tested to this standard. Both the inner tank and bund outer are manufactured to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality. Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information. Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product. As Standard

• 1” BSP Outlet
• Gauge Bung

  Options

• Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
• Ultrasonic Content Gauge
• Sight Gauge
• Clock Gauge
• Top outlet with Anti-Syphon
• 2” Fill Point
• 2” Overspill Prevention

Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date. The single skin inner tanks are manufactured to European Standard EN13343. Note: Currently there is no European Standard for bund outers, the standard is in progress at the moment and when it becomes law, all Platinum Bund outers will be tested to this standard. Both the inner tank and bund outer are manufactured to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality. Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information. Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product. As Standard

• 1” BSP Outlet
• Gauge Bung

  Options

• Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
• Ultrasonic Content Gauge
• Sight Gauge
• Clock Gauge
• Top outlet with Anti-Syphon
• 2” Fill Point
• 2” Overspill Prevention

 

Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date. The single skin inner tanks are manufactured to European Standard EN13343. Note: Currently there is no European Standard for bund outers, the standard is in progress at the moment and when it becomes law, all Platinum Bund outers will be tested to this standard. Both the inner tank and bund outer are manufactured to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality. Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information. Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product. As Standard

• 1” BSP Outlet
• Gauge Bung

  Options

• Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
• Ultrasonic Content Gauge
• Sight Gauge
• Clock Gauge
• Top outlet with Anti-Syphon
• 2” Fill Point
• 2” Overspill Prevention

Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date. All single skin oil storage tanks are manufactured to European Standard EN13343 and the manufacturing process adheres to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality. Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information. Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product. As Standard

• 1” BSP Outlet
• Gauge Bung

Options

• Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
• Ultrasonic Content Gauge
• Sight Gauge
• Clock Gauge
• Top outlet with Anti-Syphon
• 2” Fill Point
• 2” Overspill Prevention

  Diameter: 1,960mm 77.17″

Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date. All single skin oil storage tanks are manufactured to European Standard EN13343 and the manufacturing process adheres to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality. Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information. Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product. As Standard

• 1” BSP Outlet
• Gauge Bung

Options

• Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
• Ultrasonic Content Gauge
• Sight Gauge
• Clock Gauge
• Top outlet with Anti-Syphon
• 2” Fill Point
• 2” Overspill Prevention

  Diameter: 1,650mm 64.96″

Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date. All single skin oil storage tanks are manufactured to European Standard EN13343 and the manufacturing process adheres to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality. Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information. Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product. As Standard

• 1” BSP Outlet
• Gauge Bung

Options

• Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
• Ultrasonic Content Gauge
• Sight Gauge
• Clock Gauge
• Top outlet with Anti-Syphon
• 2” Fill Point
• 2” Overspill Prevention

  Diameter: 1,200mm 47.24″

Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date. All single skin oil storage tanks are manufactured to European Standard EN13343 and the manufacturing process adheres to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality. Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information. Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product. As Standard

• 1” BSP Outlet
• Gauge Bung

Options

• Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
• Ultrasonic Content Gauge
• Sight Gauge
• Clock Gauge
• Top outlet with Anti-Syphon
• 2” Fill Point
• 2” Overspill Prevention

Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date. All single skin oil storage tanks are manufactured to European Standard EN13343 and the manufacturing process adheres to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality. Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information. Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product. As Standard

• 1” BSP Outlet
• Gauge Bung

Options

• Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
• Ultrasonic Content Gauge
• Sight Gauge
• Clock Gauge
• Top outlet with Anti-Syphon
• 2” Fill Point
• 2” Overspill Prevention

Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date. All single skin oil storage tanks are manufactured to European Standard EN13343 and the manufacturing process adheres to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality. Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information. Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product. As Standard

• 1” BSP Outlet
• Gauge Bung

Options

• Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
• Ultrasonic Content Gauge
• Sight Gauge
• Clock Gauge
• Top outlet with Anti-Syphon
• 2” Fill Point
• 2” Overspill Prevention

Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date. All single skin oil storage tanks are manufactured to European Standard EN13343 and the manufacturing process adheres to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality. Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information. Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product. As Standard

• 1” BSP Outlet
• Gauge Bung

Options

• Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
• Ultrasonic Content Gauge
• Sight Gauge
• Clock Gauge
• Top outlet with Anti-Syphon
• 2” Fill Point
• 2” Overspill Prevention

Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date. All single skin oil storage tanks are manufactured to European Standard EN13343 and the manufacturing process adheres to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality. Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information. Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product. As Standard

• 1” BSP Outlet
• Gauge Bung

Options

• Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
• Ultrasonic Content Gauge
• Sight Gauge
• Clock Gauge
• Top outlet with Anti-Syphon
• 2” Fill Point
• 2” Overspill Prevention

Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date. All single skin oil storage tanks are manufactured to European Standard EN13343 and the manufacturing process adheres to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality. Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information. Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product. As Standard

• 1” BSP Outlet
• Gauge Bung

Options

• Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
• Ultrasonic Content Gauge
• Sight Gauge
• Clock Gauge
• Top outlet with Anti-Syphon
• 2” Fill Point
• 2” Overspill Prevention

Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date. All single skin oil storage tanks are manufactured to European Standard EN13343 and the manufacturing process adheres to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality. Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information. Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product. As Standard

• 1” BSP Outlet
• Gauge Bung

Options

• Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
• Ultrasonic Content Gauge
• Sight Gauge
• Clock Gauge
• Top outlet with Anti-Syphon
• 2” Fill Point
• 2” Overspill Prevention

 

Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date. All single skin oil storage tanks are manufactured to European Standard EN13343 and the manufacturing process adheres to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality. Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information. Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product. As Standard

• 1” BSP Outlet
• Gauge Bung

Options

• Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
• Ultrasonic Content Gauge
• Sight Gauge
• Clock Gauge
• Top outlet with Anti-Syphon
• 2” Fill Point
• 2” Overspill Prevention

Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date. All single skin oil storage tanks are manufactured to European Standard EN13343 and the manufacturing process adheres to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality. Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information. Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product. As Standard

• 1” BSP Outlet
• Gauge Bung

Options

• Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
• Ultrasonic Content Gauge
• Sight Gauge
• Clock Gauge
• Top outlet with Anti-Syphon
• 2” Fill Point
• 2” Overspill Prevention

Associated Documents

• 650L Rectangular Oil Tank Declaration of Performance

 

Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. Every closed water tank comes with lids fitted and a float valve backing plate for easy installation of the float valve and overflow fitting. Each product is visually inspected for defects using a light source and again prior to loading. Installation Instructions:

1. Inspect all tanks before installation as damage may occur during transport
2. Ensure that the tank is fully supported
3. Use a hole saw to drill holes in the tank
4. The centre of the float valve should be 38mm from the top of the tank
5. Do not install the tank close to a heat source such as a light or heater

Warning: To ensure uniform loading of the product, water storage tanks must be installed on a flat non-deformable base which extends beyond the product on all sides. Failure to meet this requirement will void all warranties on the product. As Standard

• Polytank Lids
• Float Valve Backing Plate

Options

• Drip Tray

 

Platinum Tanks range of cold water attic storage tanks are manufactured to European quality standards and the manufacturing process adheres to the ISO 9001:2015 quality standard. Every closed water tank comes with lids fitted and a float valve backing plate for easy installation of the float valve and overflow fitting. Each product is visually inspected for defects using a light source and again prior to loading. Installation Instructions:

1. Inspect all tanks before installation as damage may occur during transport
2. Ensure that the tank is fully supported
3. Use a hole saw to drill holes in the tank
4. The centre of the float valve should be 38mm from the top of the tank
5. Do not install the tank close to a heat source such as a light or heater

Warning: To ensure uniform loading of the product, water storage tanks must be installed on a flat non-deformable base which extends beyond the product on all sides. Failure to meet this requirement will void all warranties on the product. As Standard

• Polytank Lids
• Float Valve Backing Plate

Options

• Drip Tray