Single Skin Oil Tanks
Bunded Oil Tanks
Diesel Storage Tanks
Single Skin Oil Tanks
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date.
All single skin oil storage tanks are manufactured to European Standard EN13343 and the manufacturing process adheres to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality.
Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information.
Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product.
As Standard
- 1” BSP Outlet
- Gauge Bung
- Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
- Ultrasonic Content Gauge
- Sight Gauge
- Clock Gauge
- Top outlet with Anti-Syphon
- 2” Fill Point
- 2” Overspill Prevention
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date.
All single skin oil storage tanks are manufactured to European Standard EN13343 and the manufacturing process adheres to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality.
Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information.
Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product.
As Standard
- 1” BSP Outlet
- Gauge Bung
- Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
- Ultrasonic Content Gauge
- Sight Gauge
- Clock Gauge
- Top outlet with Anti-Syphon
- 2” Fill Point
- 2” Overspill Prevention
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date.
All single skin oil storage tanks are manufactured to European Standard EN13343 and the manufacturing process adheres to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality.
Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information.
Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product.
As Standard
- 1” BSP Outlet
- Gauge Bung
- Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
- Ultrasonic Content Gauge
- Sight Gauge
- Clock Gauge
- Top outlet with Anti-Syphon
- 2” Fill Point
- 2” Overspill Prevention
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date.
All single skin oil storage tanks are manufactured to European Standard EN13343 and the manufacturing process adheres to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality.
Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information.
Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product.
As Standard
- 1” BSP Outlet
- Gauge Bung
- Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
- Ultrasonic Content Gauge
- Sight Gauge
- Clock Gauge
- Top outlet with Anti-Syphon
- 2” Fill Point
- 2” Overspill Prevention
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date.
All single skin oil storage tanks are manufactured to European Standard EN13343 and the manufacturing process adheres to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality.
Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information.
Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product.
As Standard
- 1” BSP Outlet
- Gauge Bung
- Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
- Ultrasonic Content Gauge
- Sight Gauge
- Clock Gauge
- Top outlet with Anti-Syphon
- 2” Fill Point
- 2” Overspill Prevention
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date.
All single skin oil storage tanks are manufactured to European Standard EN13343 and the manufacturing process adheres to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality.
Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information.
Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product.
As Standard
- 1” BSP Outlet
- Gauge Bung
- Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
- Ultrasonic Content Gauge
- Sight Gauge
- Clock Gauge
- Top outlet with Anti-Syphon
- 2” Fill Point
- 2” Overspill Prevention
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date.
All single skin oil storage tanks are manufactured to European Standard EN13343 and the manufacturing process adheres to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality.
Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information.
Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product.
As Standard
- 1” BSP Outlet
- Gauge Bung
- Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
- Ultrasonic Content Gauge
- Sight Gauge
- Clock Gauge
- Top outlet with Anti-Syphon
- 2” Fill Point
- 2” Overspill Prevention
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date.
All single skin oil storage tanks are manufactured to European Standard EN13343 and the manufacturing process adheres to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality.
Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information.
Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product.
As Standard
- 1” BSP Outlet
- Gauge Bung
- Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
- Ultrasonic Content Gauge
- Sight Gauge
- Clock Gauge
- Top outlet with Anti-Syphon
- 2” Fill Point
- 2” Overspill Prevention
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date.
All single skin oil storage tanks are manufactured to European Standard EN13343 and the manufacturing process adheres to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality.
Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information.
Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product.
As Standard
- 1” BSP Outlet
- Gauge Bung
- Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
- Ultrasonic Content Gauge
- Sight Gauge
- Clock Gauge
- Top outlet with Anti-Syphon
- 2” Fill Point
- 2” Overspill Prevention
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date.
All single skin oil storage tanks are manufactured to European Standard EN13343 and the manufacturing process adheres to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality.
Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information.
Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product.
As Standard
- 1” BSP Outlet
- Gauge Bung
- Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
- Ultrasonic Content Gauge
- Sight Gauge
- Clock Gauge
- Top outlet with Anti-Syphon
- 2” Fill Point
- 2” Overspill Prevention
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date.
All single skin oil storage tanks are manufactured to European Standard EN13343 and the manufacturing process adheres to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality.
Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information.
Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product.
As Standard
- 1” BSP Outlet
- Gauge Bung
- Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
- Ultrasonic Content Gauge
- Sight Gauge
- Clock Gauge
- Top outlet with Anti-Syphon
- 2” Fill Point
- 2” Overspill Prevention
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date.
All single skin oil storage tanks are manufactured to European Standard EN13343 and the manufacturing process adheres to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality.
Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information.
Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product.
As Standard
- 1” BSP Outlet
- Gauge Bung
- Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
- Ultrasonic Content Gauge
- Sight Gauge
- Clock Gauge
- Top outlet with Anti-Syphon
- 2” Fill Point
- 2” Overspill Prevention
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date.
All single skin oil storage tanks are manufactured to European Standard EN13343 and the manufacturing process adheres to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality.
Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information.
Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product.
As Standard
- 1” BSP Outlet
- Gauge Bung
- Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
- Ultrasonic Content Gauge
- Sight Gauge
- Clock Gauge
- Top outlet with Anti-Syphon
- 2” Fill Point
- 2” Overspill Prevention
AdBlue Storage Tanks
Bunded Oil Tanks
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date.
The single skin inner tanks are manufactured to European Standard EN13343. Note: Currently there is no European Standard for bund outers, the standard is in progress at the moment and when it becomes law, all Platinum Bund outers will be tested to this standard. Both the inner tank and bund outer are manufactured to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality.
Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information.
Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product.
As Standard
- 1” BSP Outlet
- Gauge Bung
- Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
- Ultrasonic Content Gauge
- Sight Gauge
- Clock Gauge
- Top outlet with Anti-Syphon
- 2” Fill Point
- 2” Overspill Prevention
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date.
The single skin inner tanks are manufactured to European Standard EN13343. Note: Currently there is no European Standard for bund outers, the standard is in progress at the moment and when it becomes law, all Platinum Bund outers will be tested to this standard. Both the inner tank and bund outer are manufactured to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality.
Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information.
Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product.
As Standard
- 1” BSP Outlet
- Gauge Bung
- Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
- Ultrasonic Content Gauge
- Sight Gauge
- Clock Gauge
- Top outlet with Anti-Syphon
- 2” Fill Point
- 2” Overspill Prevention
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date.
The single skin inner tanks are manufactured to European Standard EN13343. Note: Currently there is no European Standard for bund outers, the standard is in progress at the moment and when it becomes law, all Platinum Bund outers will be tested to this standard. Both the inner tank and bund outer are manufactured to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality.
Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information.
Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product.
As Standard
- 1” BSP Outlet
- Gauge Bung
- Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
- Ultrasonic Content Gauge
- Sight Gauge
- Clock Gauge
- Top outlet with Anti-Syphon
- 2” Fill Point
- 2” Overspill Prevention
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date.
The single skin inner tanks are manufactured to European Standard EN13343. Note: Currently there is no European Standard for bund outers, the standard is in progress at the moment and when it becomes law, all Platinum Bund outers will be tested to this standard. Both the inner tank and bund outer are manufactured to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality.
Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information.
Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product.
As Standard
- 1” BSP Outlet
- Gauge Bung
- Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
- Ultrasonic Content Gauge
- Sight Gauge
- Clock Gauge
- Top outlet with Anti-Syphon
- 2” Fill Point
- 2” Overspill Prevention
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date.
The single skin inner tanks are manufactured to European Standard EN13343. Note: Currently there is no European Standard for bund outers, the standard is in progress at the moment and when it becomes law, all Platinum Bund outers will be tested to this standard. Both the inner tank and bund outer are manufactured to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality.
Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information.
Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product.
As Standard
- 1” BSP Outlet
- Gauge Bung
- Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
- Ultrasonic Content Gauge
- Sight Gauge
- Clock Gauge
- Top outlet with Anti-Syphon
- 2” Fill Point
- 2” Overspill Prevention
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date.
The single skin inner tanks are manufactured to European Standard EN13343. Note: Currently there is no European Standard for bund outers, the standard is in progress at the moment and when it becomes law, all Platinum Bund outers will be tested to this standard. Both the inner tank and bund outer are manufactured to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality.
Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information.
Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product.
As Standard
- 1” BSP Outlet
- Gauge Bung
- Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
- Ultrasonic Content Gauge
- Sight Gauge
- Clock Gauge
- Top outlet with Anti-Syphon
- 2” Fill Point
- 2” Overspill Prevention
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date.
The single skin inner tanks are manufactured to European Standard EN13343. Note: Currently there is no European Standard for bund outers, the standard is in progress at the moment and when it becomes law, all Platinum Bund outers will be tested to this standard. Both the inner tank and bund outer are manufactured to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality.
Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information.
Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product.
As Standard
- 1” BSP Outlet
- Gauge Bung
- Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
- Ultrasonic Content Gauge
- Sight Gauge
- Clock Gauge
- Top outlet with Anti-Syphon
- 2” Fill Point
- 2” Overspill Prevention
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date.
The single skin inner tanks are manufactured to European Standard EN13343. Note: Currently there is no European Standard for bund outers, the standard is in progress at the moment and when it becomes law, all Platinum Bund outers will be tested to this standard. Both the inner tank and bund outer are manufactured to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality.
Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information.
Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product.
As Standard
- 1” BSP Outlet
- Gauge Bung
- Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
- Ultrasonic Content Gauge
- Sight Gauge
- Clock Gauge
- Top outlet with Anti-Syphon
- 2” Fill Point
- 2” Overspill Prevention
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for ease of installation. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date.
The single skin inner tanks are manufactured to European Standard EN13343. Note: Currently there is no European Standard for bund outers, the standard is in progress at the moment and when it becomes law, all Platinum Bund outers will be tested to this standard. Both the inner tank and bund outer are manufactured to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality.
Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information.
Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product.
As Standard
- 1” BSP Outlet
- Gauge Bung
- Tank Pack (1”/0.5” reducer, fuel filter with shut off valve)
- Ultrasonic Content Gauge
- Sight Gauge
- Clock Gauge
- Top outlet with Anti-Syphon
- 2” Fill Point
- 2” Overspill Prevention
Diesel Storage Tanks
Platinum Tanks range of bunded fuel stations feature a piusi fuel pump fitted with a 10 micron particulate filter and a 4m hose with automatic shut-off nozzle.
Both the inner tank and bund outer are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 2” fill point is fitted to the inner tank to enable easy filling of the inner tank. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date.
Platinum Tanks bunded fuel stations are manufactured to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality.
Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information.
Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product.
As Standard
- Piusi Pump
- 4m Hose Pack with Auto Shut-Off Nozzle
- Gauge Bung
- Alternative Hose Lengths
- Ultrasonic Content Gauge
- Sight Gauge
- Clock Gauge
- Top outlet with Anti-Syphon
- 2” Fill Point
- 2” Overspill Prevention
Platinum Tanks range of oil storage tanks are suitable for use as gravity feed fuel tanks. The tanks can be fitted with a hose pack and auto cut off nozzle.
All fuel storage tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is fitted to every tank for ease of installation. Each fuel tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date.
All products are manufactured to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality.
Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information.
Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product.
As Standard
- 4m Hose Pack with Auto Shut-Off Nozzle
- Gauge Bung
- Alternative Hose Lengths
- Ultrasonic Content Gauge
- Sight Gauge
- Clock Gauge
- Top outlet with Anti-Syphon
- 2” Fill Point
- 2” Overspill Prevention
Platinum Tanks range of bunded fuel stations feature a piusi fuel pump fitted with a 10 micron particulate filter and a 4m hose with automatic shut-off nozzle.
Both the inner tank and bund outer are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 2” fill point is fitted to the inner tank to enable easy filling of the inner tank. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date.
Platinum Tanks bunded fuel stations are manufactured to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality.
Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information.
Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product.
As Standard
- Piusi Pump
- 4m Hose Pack with Auto Shut-Off Nozzle
- Gauge Bung
- Alternative Hose Lengths
- Ultrasonic Content Gauge
- Sight Gauge
- Clock Gauge
- Top outlet with Anti-Syphon
- 2” Fill Point
- 2” Overspill Prevention
Platinum Tanks range of bunded fuel stations feature a piusi fuel pump fitted with a 10 micron particulate filter and a 4m hose with automatic shut-off nozzle.
Both the inner tank and bund outer are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 2” fill point is fitted to the inner tank to enable easy filling of the inner tank. The inner tank comes fitted with a gauge bung which can be removed in order to fit an ultrasonic sensor at a later date.
Platinum Tanks bunded fuel stations are manufactured to the ISO 9001:2015 quality standard. Each product is visually inspected for defects throughout production and prior to loading. All single skin liquid storage tanks are pneumatically pressure tested to ensure maximum product quality.
Fuel storage tanks are not suitable for the storage of drinking water however all fuel storage tanks can be manufactured from potable grade material. Please view the water storage section or contact sales for more information.
Warning: To ensure uniform loading of the product, liquid storage tanks must be installed on a flat non-deformable, non-combustible base which extends 300mm from the product on all sides. When full an oil tank will expand, a gap of 100m should be left surrounding the product to accommodate this expansion. To avoid leakage, the 1” outlet must be held while fitting the pipework to the tank. Failure to meet these requirements will void all warranties on the product.
As Standard
- Piusi Pump
- 4m Hose Pack with Auto Shut-Off Nozzle
- Gauge Bung
- Alternative Hose Lengths
- Ultrasonic Content Gauge
- Sight Gauge
- Clock Gauge
- Top outlet with Anti-Syphon
- 2” Fill Point
- 2” Overspill Prevention
Single Skin Oil Tanks
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for eas
Read More
Length:
1,450mm (57″)
Width:
540mm (21.25″)
Height:
1,210mm (47.6″)
Capacity:
650 Litres (171 Gallons)
Warranty:
2 Years on Manufacturing Defects. Product must be registered at www.platinum-tanks.ie/product-registration. Warranty covers replacement tank only. 1 Year on Parts.
Diameter:
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for eas
Read More
Length:
1,440mm (56.75″)
Width:
660mm (26″)
Height:
1,220mm (48″)
Capacity:
950 Litres (210 Gallons)
Warranty:
2 Years on Manufacturing Defects. Product must be registered at www.platinum-tanks.ie/product-registration. Warranty covers replacement tank only. 1 Year on Parts.
Diameter:
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for eas
Read More
Length:
1,780mm (70″)
Width:
530mm (20.8″)
Height:
1,450mm (51″)
Capacity:
1,000 Litres (220 Gallons)
Warranty:
2 Years on Manufacturing Defects. Product must be registered at www.platinum-tanks.ie/product-registration. Warranty covers replacement tank only. 1 Year on Parts.
Diameter:
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for eas
Read More
Length:
1,770mm (70″)
Width:
660mm (26″)
Height:
1,270mm (50″)
Capacity:
1,150 Litres (252 Gallons)
Warranty:
2 Years on Manufacturing Defects. Product must be registered at www.platinum-tanks.ie/product-registration. Warranty covers replacement tank only. 1 Year on Parts.
Diameter:
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for eas
Read More
Length:
1,935mm (76.18″)
Width:
680mm (26.77″)
Height:
1,450mm (57.09″)
Capacity:
1,230 Litres (271 Gallons)
Warranty:
2 Years on Manufacturing Defects. Product must be registered at www.platinum-tanks.ie/product-registration. Warranty covers replacement tank only. 1 Year on Parts.
Diameter:
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for eas
Read More
Length:
1,960mm (77")
Width:
980mm (38.5")
Height:
1,030mm (40.5")
Capacity:
1,100 Litres (240 Gallons)
Warranty:
2 Years on Manufacturing Defects
Diameter:
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for eas
Read More
Length:
1,620mm (66″)
Width:
1,100mm (44″)
Height:
1,180mm (47″)
Capacity:
1,360 Litres (300 Gallons)
Warranty:
2 Years on Manufacturing Defects2 Years on Manufacturing Defects. Product must be registered at www.platinum-tanks.ie/product-registration. Warranty covers replacement tank only. 1 Year on Parts.
Diameter:
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for eas
Read More
Length:
1,950mm (78″)
Width:
1,200mm (48″)
Height:
1,270m (50″)
Capacity:
2,000 Litres (440 Gallons)
Warranty:
2 Years on Manufacturing Defects. Product must be registered at www.platinum-tanks.ie/product-registration. Warranty covers replacement tank only. 1 Year on Parts.
Diameter:
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for eas
Read More
Length:
2,150mm (85″)
Width:
1,300mm (54″)
Height:
1,380mm (55″)
Capacity:
2,560 Litres (550 Gallons)
Warranty:
2 Years on Manufacturing Defects. Product must be registered at www.platinum-tanks.ie/product-registration. Warranty covers replacement tank only. 1 Year on Parts.
Diameter:
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for eas
Read More
Length:
1,830mm (72″)
Width:
1,060mm (41.7″)
Height:
890mm (35″)
Capacity:
1,230 Litres (270 Gallons)
Warranty:
2 Years on Manufacturing Defects. Product must be registered at www.platinum-tanks.ie/product-registration. Warranty covers replacement tank only. 1 Year on Parts.
Diameter:
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for eas
Read More
Length:
Width:
Height:
1,450mm (57.09″)
Capacity:
1,3600 Litres (300 Gallons)
Warranty:
2 Years on Manufacturing Defects. Product must be registered at www.platinum-tanks.ie/product-registration. Warranty covers replacement tank only. 1 Year on Parts.
Diameter:
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for eas
Read More
Length:
Width:
Height:
1,450mm (57.09″)
Capacity:
2,500 Litres (550 Gallons)
Warranty:
2 Years on Manufacturing Defects. Product must be registered at www.platinum-tanks.ie/product-registration. Warranty covers replacement tank only. 1 Year on Parts.
Diameter:
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for eas
Read More
Length:
Width:
Height:
2,120mm (83.46″)
Capacity:
5,000 Litres (1,100 Gallons)
Warranty:
2 Years on Manufacturing Defects. Product must be registered at www.platinum-tanks.ie/product-registration. Warranty covers replacement tank only. 1 Year on Parts.
Diameter:
AdBlue Storage Tanks
Length:
1,870mm (73.60″)
Width:
1,300mm (51.18″)
Height:
1,595mm (62.80″)
Capacity:
1,360 Litres (300 Gallons)
Warranty:
10 Years on Manufacturing Defects. Product must be registered at www.platinum-tanks.ie/product-registration. Warranty covers replacement tank only. 1 Year on Parts.
Diameter:
Length:
2,430mm (95.67″)
Width:
1,480mm (58.27″)
Height:
1,830mm (72.05″)
Capacity:
2,500 Litres (550 Gallons)
Warranty:
10 Years on Manufacturing Defects. Product must be registered at www.platinum-tanks.ie/product-registration. Warranty covers replacement tank only. 1 Year on Parts.
Diameter:
Diameter Min: 2,190mm 86.22″
Diameter Max: 2,890mm 113.78″
Length:
Width:
Height:
2,400mm (94.49″)
Capacity:
5,000 Litres (1,100 Gallons)
Warranty:
10 Years on Manufacturing Defects. Product must be registered at www.platinum-tanks.ie/product-registration. Warranty covers replacement tank only. 1 Year on Parts.
Diameter:
Bunded Oil Tanks
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for eas
Read More
Length:
1,550mm (65″)
Width:
680mm (26.7″)
Height:
1,600mm (63″)
Capacity:
650 Litres (171 Gallons)
Warranty:
10 Years on Manufacturing Defects. Product must be registered at www.platinum-tanks.ie/product-registration. Warranty covers replacement tank only. 1 Year on Parts.
Diameter:
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for eas
Read More
Length:
1,890mm (74.4″)
Width:
690mm (27.17”)
Height:
1,530mm (60″)
Capacity:
1,000 Litres (220 Gallons)
Warranty:
10 Years on Manufacturing Defects. Product must be registered at www.platinum-tanks.ie/product-registration. Warranty covers replacement tank only. 1 Year on Parts.
Diameter:
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for eas
Read More
Length:
2,250mm (88.58″)
Width:
910mm (35.83″)
Height:
1,610mm (63.39″)
Capacity:
1,230 Litres (271 Gallons)
Warranty:
10 Years on Manufacturing Defects. Product must be registered at www.platinum-tanks.ie/product-registration. Warranty covers replacement tank only. 1 Year on Parts.
Diameter:
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for eas
Read More
Length:
1,870mm (73.62″)
Width:
1,300mm (51.18″)
Height:
1,350mm (53.15″)
Capacity:
1,360 Litres (300 Gallons)
Warranty:
10 Years on Manufacturing Defects10 Years on Manufacturing Defects. Product must be registered at www.platinum-tanks.ie/product-registration. Warranty covers replacement tank only. 1 Year on Parts.
Diameter:
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for eas
Read More
Length:
2,230mm (87.80″)
Width:
1,400mm (55.10″)
Height:
1,420mm (55.90″)
Capacity:
2,000 Litres (440 Gallons)
Warranty:
10 Years on Manufacturing Defects. Product must be registered at www.platinum-tanks.ie/product-registration. Warranty covers replacement tank only. 1 Year on Parts.
Diameter:
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for eas
Read More
Length:
2,430mm (95.67″)
Width:
1,480mm (58.27″)
Height:
1,575mm (62.01″)
Capacity:
2,500 Litres (550 Gallons)
Warranty:
10 Years on Manufacturing Defects. Product must be registered at www.platinum-tanks.ie/product-registration. Warranty covers replacement tank only. 1 Year on Parts.
Diameter:
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for eas
Read More
Length:
Width:
Height:
1,630mm (64.17″)
Capacity:
1,360 Litres (300 Gallons)
Warranty:
10 Years on Manufacturing Defects. Product must be registered at www.platinum-tanks.ie/product-registration. Warranty covers replacement tank only. 1 Year on Parts.
Diameter:
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for eas
Read More
Length:
Width:
Height:
1,625mm (63.98″)
Capacity:
2,500 Litres (550 Gallons)
Warranty:
10 Years on Manufacturing Defects. Product must be registered at www.platinum-tanks.ie/product-registration. Warranty covers replacement tank only. 1 Year on Parts.
Diameter:
Platinum Tanks range of bunded oil tanks are manufactured from UV stabilised linear low density polyethylene to protect the product from UV degradation. A standard 1” BSP outlet is extended from the inner oil tank through the bund for eas
Read More
Length:
Width:
Height:
2,400mm (94.49″)
Capacity:
5,000 Litres (1,100 Gallons)
Warranty:
10 Years on Manufacturing Defects. Product must be registered at www.platinum-tanks.ie/product-registration. Warranty covers replacement tank only. 1 Year on Parts.
Diameter:
Diesel Storage Tanks
Platinum Tanks range of bunded fuel stations feature a piusi fuel pump fitted with a 10 micron particulate filter and a 4m hose with automatic shut-off nozzle.
Both the inner tank and bund outer are manufactured from UV stabilised linear lo
Read More
Length:
1,870mm (73.60″)
Width:
1,300mm (51.18″)
Height:
1,595mm (62.80″)
Capacity:
1,360 Litres (300 Gallons)
Warranty:
10 Years on Manufacturing Defects. Product must be registered at www.platinum-tanks.ie/product-registration. Warranty covers replacement tank only. 1 Year on Parts.
Diameter:
Platinum Tanks range of oil storage tanks are suitable for use as gravity feed fuel tanks. The tanks can be fitted with a hose pack and auto cut off nozzle.
All fuel storage tanks are manufactured from UV stabilised linear low density polye
Read More
Length:
Width:
Height:
Capacity:
Warranty:
2 Years on Manufacturing Defects
Diameter:
Platinum Tanks range of bunded fuel stations feature a piusi fuel pump fitted with a 10 micron particulate filter and a 4m hose with automatic shut-off nozzle.
Both the inner tank and bund outer are manufactured from UV stabilised linear lo
Read More
Length:
2,430mm (95.67″)
Width:
1,480mm (58.27″)
Height:
1,830mm (72.05″)
Capacity:
2,500 Litres (550 Gallons)
Warranty:
10 Years on Manufacturing Defects. Product must be registered at www.platinum-tanks.ie/product-registration. Warranty covers replacement tank only. 1 Year on Parts.
Diameter:
Platinum Tanks range of bunded fuel stations feature a piusi fuel pump fitted with a 10 micron particulate filter and a 4m hose with automatic shut-off nozzle.
Both the inner tank and bund outer are manufactured from UV stabilised linear lo
Read More
Length:
Width:
Height:
2,400mm (94.49″)
Capacity:
5,000 Litres (1,100 Gallons)
Warranty:
10 Years on Manufacturing Defects. Product must be registered at www.platinum-tanks.ie/product-registration. Warranty covers replacement tank only. 1 Year on Parts.
Diameter: